As the name suggests Non-Welded Piping involves joining pipes using no welding. Ok, but how is it beneficial? Why not stick to traditional methods like welding? – You may ask. Well, let us explain them below:
Non Welded Piping Technology is clean as there is no welding. There is no problem of weld contaminants remaining in the hydraulic system and damaging the hydraulic machinery due to improper flushing.
Non-Welded piping inherits a lot of cost benefits. The supporting proof is that it does not require any skilled or specialized labour (based on the materials like CS, SS, and CuNi), since an unskilled person with installation knowledge of the Non-Welded fitting can easily carry out the assembly. Skilled welders are very scarce and they demand huge remunerations which is a burden to any organization. Implementing Non-Welded technology will comfortably solve the above problem. Weld joints require the pipe to be acid flushed to remove the impurities and post that be inspected by x-ray test, DPT or ultrasound. These processes are not required by or applicable to Non-Welded systems since they are clean and are joined by reliable /proven seals. Non-Welded is cost-effective over the entire life cycle of the piping system; since it is cheaper to repair due to the use of seals.
Non-Welded Piping technology is a safe and secure method for assembling pipes; since there is no hot work, there is no question of any hazards. There is no need of obtaining safety permits or evacuate sensitive equipment in the vicinity of the work area which is tedious. There is also an advantage of avoiding any disruption of important activities like bunkering, tank smearing, etc. There are also no process hazards like exposure to radiation in the case of welding.
- Reduced Installation Time : Pre-Fabricated Non-Welded Piping Systems are quick to install as the Pipes are already fabricated, cleaned, flushed and painted at the factory. It involves only the installation of the prefabricated piping spools at the site. Conventional Welding involves fabricating on-site which is time-consuming. Also, after welding at site cleaning and painting is still required and all these processes can create a mess in a laboratory environment. Welding also creates a potential for fire and smoke at site which is not ideal.
- Pressure Testing – for a non-welded system pressure testing is completed with the system oil and HPUs prior to flushing activities. If any leakages are detected (due to improper flange assembly by the installer) at the flange connection then all that is required is disassembly, new O-rings and re-assembly. For a welded system if leaks are detected then the pipe needs to be fully emptied and oil removed. Then grinding and rework of the weld are applied. This process to fix a weld is significantly longer to complete and more common to happen compared to a non-welded joint.
- Reduced Flushing Times – Flushing in a Non-welded piping system is generally done to clean the oil (all new oil is delivered in a condition that requires cleaning to the systems requirements) and remove any environmental contaminants entered during the site assembly phase. A prefabricated non-welded Tube-Mac system is delivered precleaned from the factory and ready for installation. Also, the pipe used for the non-welded system is a cold-drawn, precision tube line that has a smooth internal surface with no mill scale present. In this case, flushing can be completed with the system oil and System HPU(s) as you are generally cleaning the new oil and light environment contamination. For a Conventional Welded piping system flushing is a major activity that involves three steps:
- Degrease/Chemical/Acid Flushing and physical agitation (striking weld joints with a hammer to loosen scale/weld slag)
- Neutralizing (removal of all chemicals/acids) and drying (removal of all water)
- Oil Flushing (this process is considerably longer than that done for Non-Welded Piping System)
- Even after flushing a welded system, there is no guarantee that all the slag or scale has been removed so over time this can break loose and cause expensive damage to the sensitive servo valves, pumps, and actuators.
- Certified Product – The connections in the Non-Welded Piping system are reliable as they are approved by major classification societies like DNV/LR/ABS and inspection of the fabricated joint is easy and inexpensive. In a Conventional Welding System, reliability cannot be assured in case inspection is not done by using expensive inspection techniques like Radiographic Test.
- Better Vibration Resistance– In a Non-Welded Piping System the sealing is done through seal carriers (Flare cone or Seal Retainer) as opposed to a Conventional Welding system where sealing is at the flanges.
- Heavy Vibrations have a high impact on Welded System Flanges as the flanges are fixed which is not the case in Non-Welded System where the flanges can flex. Furthermore, since the orientation of the weld flange in the spool cannot be changed, they are likely that they are forced into place to match the mating flange applying additional loads on the weld leading to premature failure. Hence there is a probability of Welded System Joints failing at high-vibration loads.
- Preferred Method – Non-Welded is a generally accepted and preferred method for Hardline Piping connections in laboratory and testing industries due to the proven long-term durability and cleanliness it provides compared to welded joints.